Tenga Flip Zero Red & Warmer Set

Introducing the Tenga Flip Zero Red, the new addition to the Flip 0 series, designed to provide a lifelike sensation that closely resembles the warmth and texture of a pure female body.

The Flip Zero Red offers a soft and pleasurable experience, similar to the Flip Zero White, but with an entirely new internal texture. It is available for purchase only as a set with the Warmer Set. The Warmer Set is a device that provides gentle warmth to enhance the lifelike experience when inserting it into the Flip Zero. It can be used with Flip 0, Flip 0 EV, Flip ORB, and Flip Hole.

Order today and receive a free 250ml bottle of Nuru. Free Kerry Express shipping is available, and express delivery service is provided.

The Tenga Flip Zero Red & Warmer Set includes:

1. Product Body
2. Transparent case to protect the product from dust and dirt.
3. Slide Arms
4. Heat Stick
5. Stand
6. Heat Stick Case
7. AC Adapter
8. Tenga Hole Lotion Real: Two sachets of lubricant for testing and initial use.
9. Transport Protection Cap (can be discarded after opening).

Components of the heating element.

• A Touch Button (touch-sensitive operation)
• B LED light indicating the operational status
• C Waterproof cap for charging port
• D Charging port

Placing the Flip Cup into the Stand to prepare for warming.

1. Connect the Heat Stick to the Stand by aligning the Heat Stick Tab with the groove on the Stand.
2. Remove the water-resistant cap from the Stand and connect the charging cable to the charging port.
3. Open the Flip Cup to insert the lubricant.
   • Slide the Slide Arms out of the Cup.
   • Use your thumbs and index fingers of both hands to gently squeeze and pull the top joint until the lock clicks out (do not apply excessive force as it may cause the lock to break).
   • Do not extend the Flip Cup too far as it may damage the product. It is recommended not to extend it beyond 130 degrees.
4. Apply lubricant inside the Cup, then close the Cup by aligning it with the Slide Arms and lubricate the entry point.
5. Apply lubricant to the end of the Heat Stick, then slowly insert the Flip Cup onto the Heat Stick by squeezing the Pressure Pad and holding it. Then, gradually insert the Cup straight until it reaches the base, while squeezing to release the air inside.

How to use the Flip Warmer to warm up:

1. Once you have attached the Flip Cup to the Stand for warming, simply touch the touch button for 2 seconds to turn on the device (and touch it for 2 seconds to turn off the device when desired).
2. The Flip Cup is ready to use when the LED light stops flashing.
3. While the device is running, quickly tapping the touch button twice will change the mode between HIGH and LOW (the device is initially set to HIGH mode when turned on).
4. In HIGH mode, the light will blink brightly for one second.
5. In LOW mode, the light will blink softly for two seconds.
6. The device will switch to the warming mode when the LED light stops flashing.
7. The device will automatically turn off if the touch button is not used for more than 30 minutes.

How to remove the Flip Cup from the Flip Warmer after warming:

1. To remove the Flip Cup from the Heat Stick, squeeze the upper part of the cup to push the Heat Stick out while gently lifting the cup.
2. If the Heat Stick comes off along with the removed cup, hold the base of the Heat Stick and slowly pull it out.
3. After warming up the Flip Cup, don't forget to use your finger to check the internal temperature before use.

Models compatible with the Warmer Set and general warming time:

The general warming time High mode (meaning until the LED light stops flashing) mentioned above is based on measurements taken in Japan at room temperatures of 15-23°C. If the room temperature is higher like in Thailand, it may require more time for warming.

• FLIP 0 Series / Warming time: Approximately 5 minutes
• FLIP 0 Series / Warming time: Approximately 5 minutes
• FLIP ORB Series / Warming time: Approximately 5 minutes
• FLIP HOLE Series / Warming time: Approximately 5 minutes